ppgi coil-manufacture,factory,supplier from China

And cold-rolled coil (annealed state): it is obtained by bell-type annealing before the chilled coil is rolled. After annealing, its work hardening phenomenon, that is, the decrease in yield strength is close to that before cold rolling.Definition of cold rolled coilCold-rolled coils are made of hot-rolled coils, which are rolled at room temperature below the recrystallization temperature, including plates and coils.

The production process of galvanized coil mainly has two kinds of hot dip galvanizing and electric galvanizing, the following is a detailed introduction:Hot-dip galvanizing processSurface pretreatment: First of all, the surface treatment of the steel plate, including cleaning, oil removal and rust removal processes, to ensure that the surface of the steel plate is clean and smooth, to provide a good foundation for subsequent galvanized, enhance the adhesion of the galvanized layer 1.Pickling and phosphating: pickling is to soak the steel plate in the acid solution to remove the surface oxide a

Recently, the color roll market has shown a booming trend, and its demand is growing in many areas, which is inseparable from its continuous improvement of production technology.Substrate preparation: The substrate of the color coated coil is usually cold-rolled strip steel or hot-rolled strip steel, and some will also use hot galvanized sheet, hot aluminum plated zinc plate, electrogalvanized sheet, etc.

Color-coated coil is based on hot-dip galvanized sheet, hot-dip galvanized sheet, electro-galvanized sheet, etc. After surface pretreatment (chemical degreasing and chemical conversion treatment), one or several layers of organic coatings are applied on the surface, and then A product that is baked and cured.

Galvanized coil, a thin steel sheet that is dipped in a bath of molten zinc to adhere a layer of zinc to its surface. It is mainly produced by the continuous galvanizing process, that is, the coiled steel plate is continuously dipped in the galvanizing tank with molten zinc to make galvanized steel plate; alloyed galvanized steel plate. This kind of steel panel is also made by hot dip method, but it is heated to about 500℃ immediately after coming out of the tank, so that it can form an alloy film of zinc and iron.

Channel steel is a carbon structural steel for manufacturing and machinery. It is a section steel with a complex section, and its cross-sectional shape is groove-shaped. Channel steel is mainly used in building structure, curtain wall engineering, mechanical equipment and vehicle manufacturing. In use, it is required to have good welding, riveting performance and comprehensive mechanical performance.The raw material billet for producing channel steel is carbon-structured steel or low-alloy steel billet with a carbon content not exceeding 0.25%.

Corrugated board is also called profiled plate. It adopts color coated steel plate, galvanized sheet and other metal sheets to be rolled and cold-bent into various corrugated profiled plates. It is suitable for industrial and civil buildings, warehouses, special buildings, large-span Roof, wall and interior and exterior wall decoration of steel structure houses.

Galvanized steel sheet is a high-quality building material widely used in industry and construction fields. By coating a layer of anti-corrosion zinc on the surface of the steel plate, galvanized steel plates have excellent advantages over ordinary steel plates.Galvanized steel plate is a welded steel plate with a hot-dip or electroplated zinc layer on the surface.

Galvanized steel pipes are divided into cold galvanized steel pipes and hot galvanized steel pipes. Cold galvanized steel pipes have been banned, and the latter has been advocated by the state for temporary use. In the 1960s and 1970s, developed countries began to develop new types of pipes, and have banned galvanized pipes. China's Ministry of Construction and other four ministries and commissions also issued a document explicitly banning galvanized pipes as water supply pipes from 2000.

1050 aluminum is often used as metal for chemical equipment and thin plate processing parts. 1050 aluminum alloy 2000 series aluminum plate represents 2A16 (LY16) 2A06 (LY6) 2000 series aluminum plate is characterized by high hardness, among which copper metal content is the highest, about 3-5%. The 2000 series and 7000 aluminum sheets belong to aviation aluminum and are not commonly used in conventional industries. There are fewer manufacturers of 2000 series aluminum sheets in my country. The quality can not be compared with foreign countries.