Slewing bearing has four series of toothless, external and internal toothed four-point contact ball bearings, double row angular contact ball bearings cross cylindrical roller bearings, cross tapered roller bearings and three row cylindrical roller composite bearings, of which four-point contact ball bearings have higher static load capacity, cross cylindrical roller has higher dynamic load capacity, The pre-interference of cross-tapered roller bearing can make the bearing have greater support rigidity and rotation accuracy.
Contact Now
The outer diameter (OD) of the cam follower (stud or yoke) can be the standard cylindrical shape or be crowned. Crowned cam followers are used to keep the load evenly distributed if it deflects or if there is any misalignment between the follower and the followed surface. They are also used in turntable type applications to reduce skidding. Crowned followers can compensate for up to 0.5° of misalignment, while a cylindrical OD can only tolerate 0.06°. The only disadvantage is that they cannot bear as much load because of higher stresses.
Contact Now
RU cross roller bearings are also known as bearings. The main body of a rolling body usually uses cylindrical or tapered rollers to intersect a single flow path, separated by retainers or spacers, and arranged in a cross pattern. Therefore, the cross roller ring group can withstand loads in all directions, with a stiffness of 3-4 times higher than traditional models. RU cross roller bearing is lubricated by spray. Drilled shrinkage air mixes spray and lubricating oil to produce oil mist.
Contact Now
High load carrying capacity The cage bars are displaced relative to the roller pitch diameter to enable the rollers to be placed closer to each other, creating room for additional rollers High stiffness
The increased number of rollers increases radial stiffness. High speed capabilityThe cage designs are suitable for high speeds, rapid accelerations and peak loads.
Long service life
The black oxide coating of rings and rollers (designation suffix L4B) contributes to extended service life by improving:
Contact Now
In general, the rotary support bearing is an indispensable part of modern mechanical equipment, and its stability, reliability and life directly affect the operating efficiency and safety of the equipment. Therefore, in the process of engineering design and use, it is necessary to attach great importance to the selection, installation and maintenance of rotary support bearings to ensure the normal operation of the equipment and extend the service life.
Contact Now
The different types of cylindrical roller bearings are designated based on their structural features and intended applications: N..EM: Cylindrical roller bearing with a standard inner ring without any ribs, suitable for radial loads. NU..EM: Bearing with aremovable inner ring and two integral flanges on the outer ring, designed for high radial loads and accommodates axialdisplacement. NJ..EM: Features a removable inner ring and one integral flange on the outer ring, primarily used for applicationswhere axial displacement is required.
Contact Now
Rotary bearing is an important mechanical component used to support and rotate shafts, which is usually used in industrial equipment, ships, automobiles and construction machinery. It is mainly composed of an inner and outer ring, a rolling body and a cage, and realizes the rotation and support of the shaft by rolling between the inner and outer rings of the rolling body. The design and selection of rotary bearing have an important influence on the stability, reliability and operation efficiency of the equipment.
Contact Now
According to whether the ring has a rib or not, NSK cylindrical roller bearings are divided into NU, NJ, NUP, N, NF and other single-row bearings, and NNU, NN double-row bearings. The bearing is a structure with separable inner ring and outer ring. Cylindrical roller bearings with inner or outer rings without rims, the inner and outer rings can be axially moved relative to each other, so they can be used as free-end bearings.
Contact Now
Some cylindrical roller bearings have no ribs on either theinnere rings canelative to eacese can bfree-end bearingsCylindrical roller bearingouter rings has two ribs aother ringhas one ,are capable of takingxial loaone directiobearingshave high radial rigidity and are used primarily for precisionmachine tools.Types NU , N , NNU , and NN are suitable as free-end bearingsTypes NJ and NF can sustain limited axial loads in one directionTypes NH and NUP can be used as fixed-end bearingsNH-type cylindrical roller bearings consist of the Nj-type cylindricalroller bearings andHu-type Lshaped thrust co
Contact Now
Applications: Cross roller bearings are widely used in many fields, including machine tools, engineering machinery, medical equipment, food packaging machinery, etc. On machine tools, cross roller bearings are often used to support the spindle and the turntable to ensure the high-speed and high-load operation of the equipment.
Contact Now
High Rigidity Type Crossed Roller Bearing V has a solid one-piece construction for both inner and outer rings. Therefore, high accuracy and high rigidity are achieved, and mounting errors can be minimized. As separators are incorporated between the cylindrical rollers for smooth rotation, these bearings are suitable for applications where rotation speed is comparatively high.
Contact Now
1.Thrust cylindrical roller bearings are often combined into high-stiffness bearing configurations, which can withstand heavy loads and vibration loads without difficulty.2. this kind of bearing can bear a large axial load in a single direction, but can not bear radial load, they do not have automatic aligning ability.3. the thrust cylindrical roller bearing can be divided into thrust cylindrical roller and cage assembly, shaft ring and seat ring.4.
Contact Now
Structure:Internal Structure and Retainer Material VariationC: Symmetrical roller, Stamped Steel retainerCA: Symmetrical roller, one-pice brass cageCTN1: Symmetrical roller, nylon cageE: Third generation design.
Contact Now
The ball screw pair has the characteristics of high precision, reversibility and high efficiency, which is the further extension and development of the ladder screw, and the important significance of this development is to change the sliding action of the ladder screw into a rolling action.
Contact Now
Thrust cylindrical roller bearings and thrust roller bearings are suitable for low speed occasions, the thrust tapered roller bearing speed is slightly higher than the thrust cylindrical roller bearing. Bearing knowledgeThrust cylindrical roller bearings are separated bearings and can only withstandThe unidirectional axial load and slight impact can limit the axial displacement of the shaft (or housing) in one direction, so it can be used for unidirectional axial positioning. However, its carrying capacity is much greater than that of thrust ball bearings.
Contact Now
Product Description:The aluminum sheet is 1/8 inch thick (about 3.175 mm). This thickness gives it a certain degree of robustness, suitable for a variety of applications requiring a certain degree of structural strength. Decorative panels that can be used for building facades can reduce the load of building structures due to their light weight and easy installation.
Contact Now
Agricultural machinery does need better sealing performance under polluted conditions to prevent dust, moisture and particles from entering the machinery and affecting normal operation.
Contact Now
Cam Follower Needle Roller Bearings are also referred to as track follower. They are designed to follow a sliding or rotating piece (cam) and they use rollers or needles as the rolling elements. Cam Follower Bearings are therefore able to replicate a specific motion because they are highly versatile. They have thick-walled outer rings that run on a track.
Contact Now
A flange bearing is a bearing widely used in industrial machinery, which has a flange (usually circular) to be fixed in the mechanical equipment. The flange bearing consists of an inner ring, an outer ring, a rolling element (such as a steel ball, roller, roller, etc.), a cage and a seal.First of all, the inner ring and the outer ring are the main bearing parts of the flange bearing, they are usually made of high-quality steel, after a good heat treatment process to ensure their hardness and wear resistance.
Contact Now
Product Description:SS400 carbon steel can be used for some non-critical structural components of the car body, such as some reinforcement plates and brackets inside the body.
Contact Now
The sliding bearing seat is composed of an upper cover, a base, a split bearing bushing (aluminum bronze) and mounting bolts, which mainly bear radial load. Easy to use, no need to install bearings. The load-free part of the inner surface of the bearing bush is provided with an oil groove, and the lubricating oil flows into the gap through the oil inlet hole and the post groove.
Contact Now
This bearing adopts ceramic rolling element (ball or roller) made of Si3N4 material; It has excellent insulation performance, its capacitance is basically 40pf, and the insulation performance is better than that of coated bearings. At high temperature, the DC impedance can also reach the range of G ohms, and has good insulation performance. Ceramic rolling element has excellent wear resistance and low lubrication requirement. Especially suitable for high-speed, low friction, low temperature operation; It works well under dry friction conditions.
Contact Now
Railway bearing is an important component used to support and guide the rotation of railway vehicle axle, which bears the weight of the train and the force generated during operation, and can ensure the smooth operation of the train. Railway bearings play a vital role in railway transportation, and their quality and performance directly affect the safety and efficiency of trains. Railway bearing is an indispensable component in railway transportation, its structure is firm, reliable quality, wear-resistant and durable, to ensure the safety, stability and efficient operation of the train.
Contact Now
It uses axially asymmetric races. An axial load passes in a straight line through the bearing, whereas a radial load takes an oblique path that tends to want to separate the races axially. So the angle of contact on the inner race is the same as that on the outer race. Angular contact bearings better support "combined loads" (loading in both the radial and axial directions) and the contact angle of the bearing should be matched to the relative proportions of each.
Contact Now