Internal Bearing Puller Repco-manufacture,factory,supplier from China

Angle steel, commonly known as angle iron, is a long strip of steel that is perpendicular to each other and forms an angle. It's the same type of steel, just called differently. It is a section steel specially used to make shelves. It has various shapes and many long holes for people to string screws. It is mainly used for personal shelves in shopping malls and factories.

The production process of galvanized coil mainly has two kinds of hot dip galvanizing and electric galvanizing, the following is a detailed introduction:Hot-dip galvanizing processSurface pretreatment: First of all, the surface treatment of the steel plate, including cleaning, oil removal and rust removal processes, to ensure that the surface of the steel plate is clean and smooth, to provide a good foundation for subsequent galvanized, enhance the adhesion of the galvanized layer 1.Pickling and phosphating: pickling is to soak the steel plate in the acid solution to remove the surface oxide a

Galvanized steel pipes are divided into cold galvanized steel pipes and hot galvanized steel pipes. Cold galvanized steel pipes have been banned, and the latter has been advocated by the state for temporary use. In the 1960s and 1970s, developed countries began to develop new types of pipes, and have banned galvanized pipes. China's Ministry of Construction and other four ministries and commissions also issued a document explicitly banning galvanized pipes as water supply pipes from 2000.

And cold-rolled coil (annealed state): it is obtained by bell-type annealing before the chilled coil is rolled. After annealing, its work hardening phenomenon, that is, the decrease in yield strength is close to that before cold rolling.Definition of cold rolled coilCold-rolled coils are made of hot-rolled coils, which are rolled at room temperature below the recrystallization temperature, including plates and coils.

The material of carbon steel plate is plain carbon steel or carbon steel, which is a steel with a carbon content of less than 2.11% and no metal elements intentionally added. In addition to carbon, it also contains a small amount of sulfur, silicon, phosphorus, manganese and other elements .

Aluminum profiles are an vital fabric for current enterprise and life, exerting impact with special overall performance and vast application.Product characteristics1.Lightweight and excessive strength: The density of aluminum is about 2.7g/cm³, which is 1/3 of steel. It is effortless to lift and install.

A516GR60 is generally SA516GR60, which is equivalent to domestic SA516Gr70. SA516Gr60 belongs to the carbon steel plate for medium-sized stoves and low-temperature pressure vessels. It implements ASME standards. It was developed and produced by Wuyang Iron and Steel Co., Ltd. in 2006. It is widely used in petroleum, chemical, power station, boiler and other industries.

Galvanized coil, a thin steel sheet that is dipped in a bath of molten zinc to adhere a layer of zinc to its surface. It is mainly produced by the continuous galvanizing process, that is, the coiled steel plate is continuously dipped in the galvanizing tank with molten zinc to make galvanized steel plate; alloyed galvanized steel plate. This kind of steel panel is also made by hot dip method, but it is heated to about 500℃ immediately after coming out of the tank, so that it can form an alloy film of zinc and iron.

Channel steel is a carbon structural steel for manufacturing and machinery. It is a section steel with a complex section, and its cross-sectional shape is groove-shaped. Channel steel is mainly used in building structure, curtain wall engineering, mechanical equipment and vehicle manufacturing. In use, it is required to have good welding, riveting performance and comprehensive mechanical performance.The raw material billet for producing channel steel is carbon-structured steel or low-alloy steel billet with a carbon content not exceeding 0.25%.

Corrugated board is also called profiled plate. It adopts color coated steel plate, galvanized sheet and other metal sheets to be rolled and cold-bent into various corrugated profiled plates. It is suitable for industrial and civil buildings, warehouses, special buildings, large-span Roof, wall and interior and exterior wall decoration of steel structure houses.