Flat Cage Thrust Needle Bearing B-1012 Needle Roller Bearing-manufacture,factory,supplier from China

And cold-rolled coil (annealed state): it is obtained by bell-type annealing before the chilled coil is rolled. After annealing, its work hardening phenomenon, that is, the decrease in yield strength is close to that before cold rolling.Definition of cold rolled coilCold-rolled coils are made of hot-rolled coils, which are rolled at room temperature below the recrystallization temperature, including plates and coils.

The material of carbon steel plate is plain carbon steel or carbon steel, which is a steel with a carbon content of less than 2.11% and no metal elements intentionally added. In addition to carbon, it also contains a small amount of sulfur, silicon, phosphorus, manganese and other elements .

The production process of galvanized coil mainly has two kinds of hot dip galvanizing and electric galvanizing, the following is a detailed introduction:Hot-dip galvanizing processSurface pretreatment: First of all, the surface treatment of the steel plate, including cleaning, oil removal and rust removal processes, to ensure that the surface of the steel plate is clean and smooth, to provide a good foundation for subsequent galvanized, enhance the adhesion of the galvanized layer 1.Pickling and phosphating: pickling is to soak the steel plate in the acid solution to remove the surface oxide a

Corrugated board is also called profiled plate. It adopts color coated steel plate, galvanized sheet and other metal sheets to be rolled and cold-bent into various corrugated profiled plates. It is suitable for industrial and civil buildings, warehouses, special buildings, large-span Roof, wall and interior and exterior wall decoration of steel structure houses.

1050 aluminum is often used as metal for chemical equipment and thin plate processing parts. 1050 aluminum alloy 2000 series aluminum plate represents 2A16 (LY16) 2A06 (LY6) 2000 series aluminum plate is characterized by high hardness, among which copper metal content is the highest, about 3-5%. The 2000 series and 7000 aluminum sheets belong to aviation aluminum and are not commonly used in conventional industries. There are fewer manufacturers of 2000 series aluminum sheets in my country. The quality can not be compared with foreign countries.

Aluminum profiles are an vital fabric for current enterprise and life, exerting impact with special overall performance and vast application.Product characteristics1.Lightweight and excessive strength: The density of aluminum is about 2.7g/cm³, which is 1/3 of steel. It is effortless to lift and install.

Aluminum rod is a kind of aluminum product. The melting and casting of aluminum rod includes melting, purification, impurity removal, degassing, slag removal and casting process. According to the different metal elements contained in aluminum rods, aluminum rods can be roughly divided into 8 categories. IntroductionAluminum (Al) is a light metal, and its compounds are widely distributed in nature. The resources of aluminum in the earth's crust are about 40-50 billion tons, second only to oxygen and silicon, ranking third. It is the largest category of metals among metal species.

A516GR60 is generally SA516GR60, which is equivalent to domestic SA516Gr70. SA516Gr60 belongs to the carbon steel plate for medium-sized stoves and low-temperature pressure vessels. It implements ASME standards. It was developed and produced by Wuyang Iron and Steel Co., Ltd. in 2006. It is widely used in petroleum, chemical, power station, boiler and other industries.

Color-coated coil is based on hot-dip galvanized sheet, hot-dip galvanized sheet, electro-galvanized sheet, etc. After surface pretreatment (chemical degreasing and chemical conversion treatment), one or several layers of organic coatings are applied on the surface, and then A product that is baked and cured.

Aluminum tube refers to a metal tubular material that is hollow along its entire longitudinal length through extrusion processing of pure aluminum or aluminum alloy. There can be one or more closed through holes, the wall thickness and cross-section are uniform, and they are delivered in straight lines or in rolls. Widely used in automobiles, ships, aviation, electrical appliances, agriculture, electromechanical, home furnishing and other industries.