black aluminum coil stock-manufacture,factory,supplier from China

Aluminum tube refers to a metal tubular material that is hollow along its entire longitudinal length through extrusion processing of pure aluminum or aluminum alloy. There can be one or more closed through holes, the wall thickness and cross-section are uniform, and they are delivered in straight lines or in rolls. Widely used in automobiles, ships, aviation, electrical appliances, agriculture, electromechanical, home furnishing and other industries.

Aluminum plate refers to the aluminum material with a thickness of more than 0.2mm to less than 500mm, a width of more than 200mm, and a length of less than 16m. With the progress of large equipment, there are more aluminum plates that can be as wide as 600mm).Aluminum plate refers to a rectangular plate processed by rolling aluminum ingots, divided into pure aluminum plate, alloy aluminum plate, thin aluminum plate, medium-thick aluminum plate, patterned aluminum plateMaintainThe specific cleaning steps of the aluminum plate are as follows:1.

And cold-rolled coil (annealed state): it is obtained by bell-type annealing before the chilled coil is rolled. After annealing, its work hardening phenomenon, that is, the decrease in yield strength is close to that before cold rolling.Definition of cold rolled coilCold-rolled coils are made of hot-rolled coils, which are rolled at room temperature below the recrystallization temperature, including plates and coils.

Recently, the color roll market has shown a booming trend, and its demand is growing in many areas, which is inseparable from its continuous improvement of production technology.Substrate preparation: The substrate of the color coated coil is usually cold-rolled strip steel or hot-rolled strip steel, and some will also use hot galvanized sheet, hot aluminum plated zinc plate, electrogalvanized sheet, etc.

Aluminum rod is a kind of aluminum product. The melting and casting of aluminum rod includes melting, purification, impurity removal, degassing, slag removal and casting process. According to the different metal elements contained in aluminum rods, aluminum rods can be roughly divided into 8 categories. IntroductionAluminum (Al) is a light metal, and its compounds are widely distributed in nature. The resources of aluminum in the earth's crust are about 40-50 billion tons, second only to oxygen and silicon, ranking third. It is the largest category of metals among metal species.

The production process of galvanized coil mainly has two kinds of hot dip galvanizing and electric galvanizing, the following is a detailed introduction:Hot-dip galvanizing processSurface pretreatment: First of all, the surface treatment of the steel plate, including cleaning, oil removal and rust removal processes, to ensure that the surface of the steel plate is clean and smooth, to provide a good foundation for subsequent galvanized, enhance the adhesion of the galvanized layer 1.Pickling and phosphating: pickling is to soak the steel plate in the acid solution to remove the surface oxide a

1050 aluminum is often used as metal for chemical equipment and thin plate processing parts. 1050 aluminum alloy 2000 series aluminum plate represents 2A16 (LY16) 2A06 (LY6) 2000 series aluminum plate is characterized by high hardness, among which copper metal content is the highest, about 3-5%. The 2000 series and 7000 aluminum sheets belong to aviation aluminum and are not commonly used in conventional industries. There are fewer manufacturers of 2000 series aluminum sheets in my country. The quality can not be compared with foreign countries.

Aluminum profiles are an vital fabric for current enterprise and life, exerting impact with special overall performance and vast application.Product characteristics1.Lightweight and excessive strength: The density of aluminum is about 2.7g/cm³, which is 1/3 of steel. It is effortless to lift and install.

Color-coated coil is based on hot-dip galvanized sheet, hot-dip galvanized sheet, electro-galvanized sheet, etc. After surface pretreatment (chemical degreasing and chemical conversion treatment), one or several layers of organic coatings are applied on the surface, and then A product that is baked and cured.

Galvanized coil, a thin steel sheet that is dipped in a bath of molten zinc to adhere a layer of zinc to its surface. It is mainly produced by the continuous galvanizing process, that is, the coiled steel plate is continuously dipped in the galvanizing tank with molten zinc to make galvanized steel plate; alloyed galvanized steel plate. This kind of steel panel is also made by hot dip method, but it is heated to about 500℃ immediately after coming out of the tank, so that it can form an alloy film of zinc and iron.