40x68x36mm China 522 Series Two Way Thrust Ball Bearing 52208-manufacture,factory,supplier from China

Thrust ball bearings are produced as single direction or double direction thrust ball bearings. They are designed to accommodate axial loads only and must not be subjected to any radial load.Thrust ball bearings are separable, the shaft washer, housing washer(s), ball and cage assembly(s) can be mounted separately. Shaft washers have a ground bore to enable an interference fit.

The bidirectional thrust ball bearing is composed of an inner and outer sphere, a steel ball and a cage. The inner and outer spheres are spherical, the steel balls are distributed between the two spheres, and the cage is used to maintain the spacing and distribution of the steel balls. When stressed, the inner ring and the outer ring bear axial and radial forces respectively, and the steel ball transfers force by rolling.

Single direction thrust ball bearings:consist of two washers with raceways and balls guided b a cage. Washers have flat seating surfaces, and that is why they must be supported so that all balls can be evenly loaded. Bearings carry the axial load only in one direction. They are not able to carry radial forces. Double direction thrust ball bearings:have two cages with balls between the central shaft washer and two houding washers with flat seating surfaces. The shaft washer has raceways on both sides and is fixed on the journal.

As one of the leading thrust ball bearing manufacturers in China, we can provide standard thrust ball bearings, stainless steel thrust ball bearings, ceramic thrust ball bearings, one-way thrust ball bearings, thrust angular contact ball bearing, axial ball thrust bearings, miniature thrust ball bearings Bearings, banded roller thrust bearings, deep groove ball thrust bearing, bearing dimensions support metric and inches. Various sizes can also be customized according to customer needs.

· The thrust ball bearing consist of a shaft washer, a housing washer and a ball  and cage thrust assembly.· The bearings are separable so that mounting is simple as the washers and the ball and cage  assembly can be mounted separately.· The types: bearings with a flat seat surface on the housing washer, bearings with a&nbs

The structure of one-way thrust ball bearing is relatively simple, mainly composed of outer ring, inner ring, steel ball, cage and cover.The outer ring is the outermost part of the thrust ball bearing, usually made of steel material. The inner ring is located inside the outer ring, and the gap between the outer ring is the movement space of the steel ball. The steel ball is the key component connecting the outer ring and the inner ring, which can provide the function of carrying the thrust load.

The main features of rotary support bearings include high bearing capacity, fast speed, small friction, wear resistance, simple structure, easy installation and so on. It can withstand large axial and radial loads, while having high rigidity and accuracy, suitable for high-speed rotation and precision positioning requirements. Different types of rotary support bearings have differences in structural form and working principle, such as four-point contact ball type, two-way thrust ball type, cross roller type, tapered roller type and so on.

Features :Thrust ball bearings consist of two precision washers (rings) and a ball complement spaced by retainer. They can besupplied with or without radius ball grooves in the rings.

Single course thrust ball bearings: consist of two washers with raceways and balls guided b a cage. Washers have flat seating surfaces, and that is why they need to be supported so that all balls can be evenly loaded. Bearings lift the axial load solely in one direction. They are no longer capable to lift radial forces.Double path thrust ball bearings: have two cages with balls between the central shaft washer and two houding washers with flat seating surfaces.

(1)Linear motion bearing is a kind of low-cost metal for producing linear motion system, which is used for infinite stroke cylindrical shaft.. Because point contact ball bearing with shaft, so using the load is small.  (2) the flange linear bearing can be divided into: round flange type, method type, elliptical flange type, guided round flange, guiding method, guide the elliptical flange type, extended round flange type.(3)According to the specification is divided into two series of LM and LME series.

Advantage of 51118 BearingApplication scope of thrust ball bearing:It is only applicable to the parts bearing one side of axial load and low speed, such as crane hook, vertical water pump, vertical centrifuge, Jack, low-speed reducer, etc.The shaft ring, seat ring and rolling element of the bearing are separated and can be installed and disassembled separately.TypeIn addition, the bearing can bear axial load, but can not bear radial load.Composition of thrust ball bearing: the thrust ball bearing is composed of seat ring, shaft ring and steel ball cage assembly.

Linear bearings with flanges Performance: Linear bearings are a linear motion system produced at a low cost for use with unlimited travel and circular shafts. Because the bearing ball is in contact with the shaft dry point, the load is small. The steel ball rotates with very little friction resistance, thus achieving smooth motion with high precision.Flanged linear bearing series Specification classification :LME, LMK series LMH series LMFP, LMKP series with flanged linear bearing LMHP series with flanged linear bearing LME.LLMK.L series LMH.L series LMFP...

Angular contact thrust ball bearings consist of an inner, outer ring, cage, steel ball and groove, and an inner/outer ring with a spherical surface, which can withstand unidirectional and bidirectional axial loads and slight radial loads.

The unidirectional thrust ball bearing comprises a shaft ring, a seat ring and a ball-cage assembly. It can be separated and the shaft ring, seat ring, ball-cage assembly can be installed separately. Unidirectional thrust ball bearings can withstand the axial load in a single direction and can be positioned in a single direction, but must not bear any radial load.The 51130 belongs to the single direction thrust ball bearings, also called ball thrust bearings or axial deep groove ball bearings. These bearings consist of a shaft ring, a housing ring and a ball and cage assembly.

Sliding bearings are sliding friction, with large contact surface, simple structure, small volume, strong bearing capacity, good vibration resistance, but large friction coefficient, easy to generate heat, need sufficient lubrication, suitable for low speed and heavy loadRolling bearings are rolling friction, compared with sliding bearings, their contact surface is small (point contact for ball bearings, line contact for roller bearings), small friction coefficient, less heat generation; less wear and tear, good accuracy retention; suitable for higher speeds run down.

Linear motion bearing is a linear motion system produced at a low cost for use with unlimited travel and cylindrical shafts. Because the bearing ball is in point contact with the shaft, the load is small. The steel ball rotates with very little friction resistance, thus achieving smooth motion with high precision. Linear motion bearing metric and Imperial series: Standard type (LM/LME/LMB... UU), adjustable (LM/LME... UUAJ), Open (LM/LME... UUOP); Extended (LM/LME... LUU); Flange type (LMF/LMK/LMH... UU, LMEF/LMEK... UU), flange extension (LMF/LMK/LMH... LUU, LMEF/LMEK...

Ball bearing with eccentric locking collar is  outer diameter in spherical surface,internal construction is the same as deep groove ball bearings of 6200 6300 series.they both can sustain radial and axial loads.We can supply full series of UC200,UC300,SA200,SB200,UEL200,UK200,SER200,CS200,UC300 series bearings.Such bearings are often used in severe operating conditions where they are exposed to dirts,moisture and high temperature.thus,insert ball bearing are usually with grease groove and oil hole on outer ring,at suitable time,we need to replace fresh grease to secure full performance an

First, the inner and outer rings of flange bearings are usually made of high-quality steel after heat treatment to improve their hardness and wear resistance. The inner ring is a component mounted on the shaft, and the outer ring is fixed on the seat hole. The two components are connected and supported by a rolling element and a cage.The rolling body is a very important part of the bearing, usually made of steel, by the different shape of the rolling body can be divided into rolling son, needle roller, ball and roller.

Railway Bearings play an important role in both passenger and goods transport.  They have to withstand heavy loads: they work at high speeds, under a great weight, are  Rolling bearings in railway gearboxes must withstand a wide variety of operating conditions and complex environmental influences. Not only are high static and, in particular, dynamic loads present in the form of vibrations and shocks, but the rolling bearings are also operated intermittently below the permissible minimum load.

1.Needle roller bearings for stamping outer rings. There are two kinds of bearings: perforated type and sealed type. The needle roller bearing has no inner ring, and the needle roller directly contacts the surface of the shaft, so the processing accuracy and heat treatment hardness of the shaft should be the same as that of the bearing inner ring.2. Solid ring needle roller bearings solid ring needle roller bearings, commonly used solid ring needle roller bearings are NA type and RNA type.3. Roller needle bearing4. Needle roller and cage assembly.

Thrust tapered roller bearings can form a very compact bearing configuration, which can withstand very heavy axial loads, is not sensitive to impact loads, and has good rigidity. LYTBZ produces unidirectional tapered roller bearings and bidirectional tapered roller thrust bearings. The screw fixed bearing constitutes a specially designed unidirectional tapered roller thrust bearing and is filled with rollers.Thrust tapered roller bearing features:This bearing is used for rolling mill screw fixed bearing configuration.

Koyo tapered roller bearings are suitable for applications requiring simultaneous radial and axial loads, such as differential, hub, transmission and other components of automobiles, as well as wind turbines, agricultural machinery, construction machinery and other equipment requiring high load capacity and high rotation accuracy. The selection of suitable Koyo tapered roller bearings can improve the efficiency and reliability of machine equipment, reduce maintenance work and costs, and is an important bearing product widely used in various fields.

High Rigidity Type Crossed Roller Bearing V has a solid one-piece construction for both inner and outer rings. Therefore, high accuracy and high rigidity are achieved, and mounting errors can be minimized. As separators are incorporated between the cylindrical rollers for smooth rotation, these bearings are suitable for applications where rotation speed is comparatively high.

As one of the largest taper roller manufacturers in Shandong, China, in addition to the tapered roller bearings introduced above, we can also provide the following tapered roller types.