22220 Bearing-manufacture,factory,supplier from China

As an vital metallic material, carbon metal performs an vital position in many fields with its incredible performance.In the development industry, carbon metal is one of the key substances for constructing secure structures.

The production process of galvanized coil mainly has two kinds of hot dip galvanizing and electric galvanizing, the following is a detailed introduction:Hot-dip galvanizing processSurface pretreatment: First of all, the surface treatment of the steel plate, including cleaning, oil removal and rust removal processes, to ensure that the surface of the steel plate is clean and smooth, to provide a good foundation for subsequent galvanized, enhance the adhesion of the galvanized layer 1.Pickling and phosphating: pickling is to soak the steel plate in the acid solution to remove the surface oxide a

Galvanized coil, a thin steel sheet that is dipped in a bath of molten zinc to adhere a layer of zinc to its surface. It is mainly produced by the continuous galvanizing process, that is, the coiled steel plate is continuously dipped in the galvanizing tank with molten zinc to make galvanized steel plate; alloyed galvanized steel plate. This kind of steel panel is also made by hot dip method, but it is heated to about 500℃ immediately after coming out of the tank, so that it can form an alloy film of zinc and iron.

And cold-rolled coil (annealed state): it is obtained by bell-type annealing before the chilled coil is rolled. After annealing, its work hardening phenomenon, that is, the decrease in yield strength is close to that before cold rolling.Definition of cold rolled coilCold-rolled coils are made of hot-rolled coils, which are rolled at room temperature below the recrystallization temperature, including plates and coils.

Recently, the color roll market has shown a booming trend, and its demand is growing in many areas, which is inseparable from its continuous improvement of production technology.Substrate preparation: The substrate of the color coated coil is usually cold-rolled strip steel or hot-rolled strip steel, and some will also use hot galvanized sheet, hot aluminum plated zinc plate, electrogalvanized sheet, etc.

Roofing sheet is a profiled plate processed by a series of processes such as rolling and cold bending of color steel plates into various wave shapes.It not only has the excellent decorative performance of traditional clay tiles, but also has the excellent performance of modern metal tiles. It is light, strong and durable. It is the current mainstream roofing material.

1050 aluminum is often used as metal for chemical equipment and thin plate processing parts. 1050 aluminum alloy 2000 series aluminum plate represents 2A16 (LY16) 2A06 (LY6) 2000 series aluminum plate is characterized by high hardness, among which copper metal content is the highest, about 3-5%. The 2000 series and 7000 aluminum sheets belong to aviation aluminum and are not commonly used in conventional industries. There are fewer manufacturers of 2000 series aluminum sheets in my country. The quality can not be compared with foreign countries.

Color-coated coil is based on hot-dip galvanized sheet, hot-dip galvanized sheet, electro-galvanized sheet, etc. After surface pretreatment (chemical degreasing and chemical conversion treatment), one or several layers of organic coatings are applied on the surface, and then A product that is baked and cured.

Galvanized steel pipes are divided into cold galvanized steel pipes and hot galvanized steel pipes. Cold galvanized steel pipes have been banned, and the latter has been advocated by the state for temporary use. In the 1960s and 1970s, developed countries began to develop new types of pipes, and have banned galvanized pipes. China's Ministry of Construction and other four ministries and commissions also issued a document explicitly banning galvanized pipes as water supply pipes from 2000.

Angle steel, commonly known as angle iron, is a long strip of steel that is perpendicular to each other and forms an angle. It's the same type of steel, just called differently. It is a section steel specially used to make shelves. It has various shapes and many long holes for people to string screws. It is mainly used for personal shelves in shopping malls and factories.