1209 k Bearing-manufacture,factory,supplier from China

1. Centripetal needle roller and cage assembly (Type K)2, needle roller bearings with double locking rings (NA, NKI, RNA, NK)3. Single row needle roller bearing with double rib on outer ring (NA, NKI, RNA, NK)4, double row needle roller bearings with double guard (NA type, RNA type)5, stamped needle roller bearings (HK type, BK type)Note: This bearing has low cost, large bearing capacity, and is suitable for supporting structures with limited installation size. The journal surface is hardened as a rolling surface, and the bearing is pressed into the seat hole without axial positioning.

Drive pinion: steeply angled tapered roller bearings, which reduce frictional moments and allow for increased rotational speeds.Hub Bearings – Rear Axle: Tapered roller bearings with an optimized internal design to limit edge loads caused by axle deflection and heavy loads.Hub bearing – front axle: Thin angular contact ball bearing improves rigidity in a narrow space.Gearboxes: High performance deep groove ball bearings TMB/TAB for increased service life or downsizing (downsizing) with the same service life as larger bearings.Final reduction planetary gears: There is a large selection of cage

When the rotary support bearing is working, the inner and outer rings realize relative rotation through the combination of rolling elements. When the external force acts on the bearing, the load is transmitted to the inner and outer rings, and is transmitted to each other through the rolling element, achieving the carrying capacity. At the same time, the rolling motion of the rolling element reduces the friction force and improves the rotation efficiency of the bearing.

Inner and outer ring design: The inner and outer rings of the insulated bearing are made of insulating materials or special treatment, so that the current inside the bearing can not be conducted through the inner and outer rings, so as to achieve the effect of electrical insulation.Seal design: The seal design of the insulated bearing is strict, which can effectively prevent the infiltration of external media and maintain the insulation performance and stability of the bearing.

The sliding bearing seat is composed of an upper cover, a base, a split bearing bushing (aluminum bronze) and mounting bolts, which mainly bear radial load. Easy to use, no need to install bearings. The load-free part of the inner surface of the bearing bush is provided with an oil groove, and the lubricating oil flows into the gap through the oil inlet hole and the post groove.

Pillow block unitsSeated (vertical) ball bearing units consist of a seated bearing mounted in a housing that can be bolted to a support surface. In our product range, you can find units to meet almost all requirements, including units that comply with ISO standards, North American standards or Japanese Industrial Standards (JIS)Flanged ball bearing unitsThe flanged ball bearing units consist of a housing-mounted housing with a housing bearing that can be bolted to the machine wall or frame.

Thrust roller bearings are used to bear axial and radial combined loads based on axial loads, but the radial load shall not exceed 55% of the axial load.

Needle roller bearing is a common rolling bearing, using needle roller as the rolling body, can withstand the radial and axial load.Structure: Needle roller bearings are mainly composed of outer ring, inner ring, needle roller, cage and seal. The shape size of the needle roller bearing is small, saving space, suitable for limited space design.

Thrust cylindrical roller bearings and thrust roller bearings are suitable for low speed occasions, the thrust tapered roller bearing speed is slightly higher than the thrust cylindrical roller bearing. Bearing knowledgeThrust cylindrical roller bearings are separated bearings and can only withstandThe unidirectional axial load and slight impact can limit the axial displacement of the shaft (or housing) in one direction, so it can be used for unidirectional axial positioning. However, its carrying capacity is much greater than that of thrust ball bearings.

Trucks are very common tools in the transportation industry, carrying important goods and supplies. Truck bearing is one of its key components, it plays an important role in the vehicle transmission system support and operation. Its quality and running state directly affect the safety and stability of the vehicle.

The fourth era hub bearing unit is to make the steady pace commonplace joint and bearing into a whole, which solves the defect of growing the dimension of the hub due to the built-in shape of the hub and the consistent pace common joint in the prior art. The improvement of the fourth technology hub bearing unit has been successful, and it is believed that it will be broadly used in a variety of kinds of cars in the close to future.

One of the biggest features of the needle roller bearing is the design of the needle roller. The needle roller has a smaller diameter than other types of rolling elements, so it can achieve a higher load carrying capacity in a limited space.

Because the bearing ball is in contact with the bearing point, the load is small.

Product Description:Precisely 1/4 inch (about 6.35 mm) thick, this thickness gives it a certain degree of structural support and stability in a variety of applications.

As one of the largest taper roller manufacturers in Shandong, China, in addition to the tapered roller bearings introduced above, we can also provide the following tapered roller types.

Single row deep groove ball bearingSingle row deep groove ball bearing with dust coverSingle row deep groove ball bearing with dust cover and sealing ringA single row deep groove ball bearing with a stop groove and a stop ring on the outer ringSingle row deep groove ball bearingSingle row deep groove ball bearing with dust coverSingle row deep groove ball bearing with seal ringA single row deep groove ball bearing with a stop groove and a stop ring on the outer ringDeep groove ball bearing is the most representative rolling bearing, widely used.

INA bearings schaeffler group is a leading manufacturer of almost all bearing types.We are INA bearing manufacturer and can provide a full range of INA bearings. For example: INA ball bearings,INA cam follower，INA thrust bearing，iINA spherical plain bearings，INA flange bearing，INA banded thrust bearing.The following is a detailed introduction about some INA bearings, if you want to know more, please contact us, we have 24 hours online service.INA Thin Section BearingsINA Thin-walled bearings are high-precision products with low operating noise and high load carrying capacity.

In rolling bearings, the bearing ring is separated by a rolling unit (rolling element), and in slide guidance systems, the movable part slides on a static guide rail or shaft. Depending on the type of track system, the sliding layer is on movable or rigid components. The lubricating oil is embedded in the sliding layer to achieve lubrication. INA linear plain bearing is a linear positioning bearing with infinite stroke length.

Thrust roller bearings have the following application characteristics:Withstand large axial load: thrust roller bearings are suitable for mechanical equipment that needs to withstand large axial load, and have high carrying capacity and stability.High-speed rotation: thrust roller bearings can provide good support and smooth operation when rotating at high speed, suitable for fast equipment.Long service life: Because thrust roller bearings can effectively reduce friction and wear, they have a long service life and reliability.Easy installation and maintenance: thrust roller bearings have simpl

Tapered roller bearings are separate bearings. Both the inner and outer rings of the bearing have tapered raceways. This type of bearing is divided into single, double and four-row tapered roller bearings according to the number of rollers installed. Single-row tapered roller bearings can support radial loads and axial loads in one direction.The type code of tapered roller bearings is 30,000, and tapered roller bearings are separable bearings.

Some cylindrical roller bearings have no ribs on either theinnere rings canelative to eacese can bfree-end bearingsCylindrical roller bearingouter rings has two ribs aother ringhas one ,are capable of takingxial loaone directiobearingshave high radial rigidity and are used primarily for precisionmachine tools.Types NU , N , NNU , and NN are suitable as free-end bearingsTypes NJ and NF can sustain limited axial loads in one directionTypes NH and NUP can be used as fixed-end bearingsNH-type cylindrical roller bearings consist of the Nj-type cylindricalroller bearings andHu-type Lshaped thrust co

The important measure to reduce automobile fuel consumption is to design low friction torque hub bearings, and the main factors affecting the bearing friction torque is the type of bearing and preload, and the bearing seal accounted for a large proportion of the friction torque components. Therefore, improving the seal design to reduce the friction torque can significantly improve the performance of hub bearings.

The popular riding machine for a stud kind cam follower is a slot, for use with a flat head screwdriver. However, hex sockets are accessible for greater torquing ability, which is specifically beneficial for eccentric cam followers and these used in blind holes.

Product Description:Polyester coated steel coil is a kind of steel coil which is pre-coated with polyester coating on the surface of galvanized steel plate by rolling coating, etc.